C 在STM32F4发现上配置SPI
当使用示波器在引脚上进行测量时，我无法从MOSI引脚或CLK引脚获得任何数据C 在STM32F4发现上配置SPI,c,arm,spi,C,Arm,Spi,当使用示波器在引脚上进行测量时，我无法从MOSI引脚或CLK引脚获得任何数据 GPIOB->MODER |= (2 << (2*13)); //Sets pin 13 as Alternate function GPIOB->MODER |= (2 << (2*14)); //Sets pin 14 as Alternate function GPIOB
GPIOB->MODER |= (2 << (2*13)); //Sets pin 13 as Alternate function
GPIOB->MODER |= (2 << (2*14)); //Sets pin 14 as Alternate function
GPIOB->MODER |= (2 << (2*15)); //Sets pin 15 as Alternate function
GPIOB->OTYPER |= PUSH_PULL_PIN_13;
GPIOB->OTYPER |= PUSH_PULL_PIN_14;
GPIOB->OTYPER |= PUSH_PULL_PIN_15;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOB->PUPDR |= PUPDR_PULLDOWN_PIN_13; // Pull down for CLK
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_14; // Pull up for MISO
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_15; // Pull up for MOSI
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_13; // 5 för AF5 till pin 13
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_14; // 5 för AF5 till pin 14
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_15; // 5 för AF5 till pin 15
GPIOA->MODER |= MODER_INPUT_PIN_0;
GPIOD->MODER |= MODER_OUTPUT_PIN_12; //Sets pin 12 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_13; //Sets pin 13 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_14; //Sets pin 14 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_15; //Sets pin 15 as output
GPIOD->OTYPER |= PUSH_PULL_PIN_12;
GPIOD->OTYPER |= PUSH_PULL_PIN_13;
GPIOD->OTYPER |= PUSH_PULL_PIN_14;
GPIOD->OTYPER |= PUSH_PULL_PIN_15;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_12;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_12; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_13; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_14; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_15; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_12; // 0 för AF0 till pin 12
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_13; // 0 för AF0 till pin 13
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_14; // 0 för AF0 till pin 14
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_15; // 0 för AF0 till pin 15
SPI2->CR1 |= (0 << CR1_CLOCK_PHASE); //Set clockphase in CR1 register
SPI2->CR1 |= (1 << CR1_CLOCK_POLARITY); //Set polarity in CR1 register
SPI2->CR1 |= (4 << CR1_BAUD_RATE); //Set baudrate
SPI2->CR1 |= (1 << CR1_DATA_FRAME_FORMAT); //16-bit transmission
SPI2->CR1 |= (1 << CR1_ENABLE_SPI); //Enable SPI
SPI2->CR1 |= (1 << CR1_MASTER_SELECT); //MASTER SELECTION
SPI2->CR1 |= (1 << CR1_LSB_FIRST); //LSB FIRST
SPI2->CR1 |= (1 << CR1_SLAVE_SELECT); //SSI set
SPI2->CR1 |= (1 << CR1_SW_SLAVE_MANAGE); //SSM, software slave management selected, which means SSI will be used insted of I/O
SPI2->CR1 |= (0 << CR1_RECEIVE_ONLY); //Transmit and Receive
SPI2->CR1 |= (0 << CR1_CRC_TRANSFER); //NOT USED, CRC
//SPI2->CR1 |= (0 << CR1_CRC_CALCULATION); //NOT USED, CRC calculation disabled
//SPI2->CR1 |= (0 << CR1_BIDIOE); //enable transmit-only if set
SPI2->CR1 |= (0 << CR1_BIDIMODE); //1-line bidirectional mode if set
//SYSCFG->EXTICR[0] |= (0 << 0); //Enable
EXTI->IMR |= (1 << 0); //Enable interrupt
EXTI->RTSR |= (1 << 0); //set Risnig edge interrupt
EXTI->FTSR |= (0 << 0); //falling edge interrupt (disabled)
NVIC_EnableIRQ(EXTI0_IRQn);
SPI2->CR2 |= (1 << 7);
while(1){
GPIOD->ODR |= (1 << 12); // led ON
delay();
GPIOD->ODR &= ~(1 << 12); // led OFF
delay();
}
return 0;
GPIOB->MODER |= (2 << (2*13)); //Sets pin 13 as Alternate function
GPIOB->MODER |= (2 << (2*14)); //Sets pin 14 as Alternate function
GPIOB->MODER |= (2 << (2*15)); //Sets pin 15 as Alternate function
GPIOB->OTYPER |= PUSH_PULL_PIN_13;
GPIOB->OTYPER |= PUSH_PULL_PIN_14;
GPIOB->OTYPER |= PUSH_PULL_PIN_15;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOB->PUPDR |= PUPDR_PULLDOWN_PIN_13; // Pull down for CLK
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_14; // Pull up for MISO
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_15; // Pull up for MOSI
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_13; // 5 för AF5 till pin 13
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_14; // 5 för AF5 till pin 14
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_15; // 5 för AF5 till pin 15
GPIOA->MODER |= MODER_INPUT_PIN_0;
GPIOD->MODER |= MODER_OUTPUT_PIN_12; //Sets pin 12 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_13; //Sets pin 13 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_14; //Sets pin 14 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_15; //Sets pin 15 as output
GPIOD->OTYPER |= PUSH_PULL_PIN_12;
GPIOD->OTYPER |= PUSH_PULL_PIN_13;
GPIOD->OTYPER |= PUSH_PULL_PIN_14;
GPIOD->OTYPER |= PUSH_PULL_PIN_15;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_12;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_12; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_13; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_14; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_15; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_12; // 0 för AF0 till pin 12
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_13; // 0 för AF0 till pin 13
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_14; // 0 för AF0 till pin 14
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_15; // 0 för AF0 till pin 15
SPI2->CR1 |= (0 << CR1_CLOCK_PHASE); //Set clockphase in CR1 register
SPI2->CR1 |= (1 << CR1_CLOCK_POLARITY); //Set polarity in CR1 register
SPI2->CR1 |= (4 << CR1_BAUD_RATE); //Set baudrate
SPI2->CR1 |= (1 << CR1_DATA_FRAME_FORMAT); //16-bit transmission
SPI2->CR1 |= (1 << CR1_ENABLE_SPI); //Enable SPI
SPI2->CR1 |= (1 << CR1_MASTER_SELECT); //MASTER SELECTION
SPI2->CR1 |= (1 << CR1_LSB_FIRST); //LSB FIRST
SPI2->CR1 |= (1 << CR1_SLAVE_SELECT); //SSI set
SPI2->CR1 |= (1 << CR1_SW_SLAVE_MANAGE); //SSM, software slave management selected, which means SSI will be used insted of I/O
SPI2->CR1 |= (0 << CR1_RECEIVE_ONLY); //Transmit and Receive
SPI2->CR1 |= (0 << CR1_CRC_TRANSFER); //NOT USED, CRC
//SPI2->CR1 |= (0 << CR1_CRC_CALCULATION); //NOT USED, CRC calculation disabled
//SPI2->CR1 |= (0 << CR1_BIDIOE); //enable transmit-only if set
SPI2->CR1 |= (0 << CR1_BIDIMODE); //1-line bidirectional mode if set
//SYSCFG->EXTICR[0] |= (0 << 0); //Enable
EXTI->IMR |= (1 << 0); //Enable interrupt
EXTI->RTSR |= (1 << 0); //set Risnig edge interrupt
EXTI->FTSR |= (0 << 0); //falling edge interrupt (disabled)
NVIC_EnableIRQ(EXTI0_IRQn);
SPI2->CR2 |= (1 << 7);
while(1){
GPIOD->ODR |= (1 << 12); // led ON
delay();
GPIOD->ODR &= ~(1 << 12); // led OFF
delay();
}
return 0;
GPIOB->MODER |= (2 << (2*13)); //Sets pin 13 as Alternate function
GPIOB->MODER |= (2 << (2*14)); //Sets pin 14 as Alternate function
GPIOB->MODER |= (2 << (2*15)); //Sets pin 15 as Alternate function
GPIOB->OTYPER |= PUSH_PULL_PIN_13;
GPIOB->OTYPER |= PUSH_PULL_PIN_14;
GPIOB->OTYPER |= PUSH_PULL_PIN_15;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOB->PUPDR |= PUPDR_PULLDOWN_PIN_13; // Pull down for CLK
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_14; // Pull up for MISO
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_15; // Pull up for MOSI
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_13; // 5 för AF5 till pin 13
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_14; // 5 för AF5 till pin 14
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_15; // 5 för AF5 till pin 15
GPIOA->MODER |= MODER_INPUT_PIN_0;
GPIOD->MODER |= MODER_OUTPUT_PIN_12; //Sets pin 12 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_13; //Sets pin 13 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_14; //Sets pin 14 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_15; //Sets pin 15 as output
GPIOD->OTYPER |= PUSH_PULL_PIN_12;
GPIOD->OTYPER |= PUSH_PULL_PIN_13;
GPIOD->OTYPER |= PUSH_PULL_PIN_14;
GPIOD->OTYPER |= PUSH_PULL_PIN_15;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_12;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_12; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_13; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_14; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_15; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_12; // 0 för AF0 till pin 12
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_13; // 0 för AF0 till pin 13
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_14; // 0 för AF0 till pin 14
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_15; // 0 för AF0 till pin 15
SPI2->CR1 |= (0 << CR1_CLOCK_PHASE); //Set clockphase in CR1 register
SPI2->CR1 |= (1 << CR1_CLOCK_POLARITY); //Set polarity in CR1 register
SPI2->CR1 |= (4 << CR1_BAUD_RATE); //Set baudrate
SPI2->CR1 |= (1 << CR1_DATA_FRAME_FORMAT); //16-bit transmission
SPI2->CR1 |= (1 << CR1_ENABLE_SPI); //Enable SPI
SPI2->CR1 |= (1 << CR1_MASTER_SELECT); //MASTER SELECTION
SPI2->CR1 |= (1 << CR1_LSB_FIRST); //LSB FIRST
SPI2->CR1 |= (1 << CR1_SLAVE_SELECT); //SSI set
SPI2->CR1 |= (1 << CR1_SW_SLAVE_MANAGE); //SSM, software slave management selected, which means SSI will be used insted of I/O
SPI2->CR1 |= (0 << CR1_RECEIVE_ONLY); //Transmit and Receive
SPI2->CR1 |= (0 << CR1_CRC_TRANSFER); //NOT USED, CRC
//SPI2->CR1 |= (0 << CR1_CRC_CALCULATION); //NOT USED, CRC calculation disabled
//SPI2->CR1 |= (0 << CR1_BIDIOE); //enable transmit-only if set
SPI2->CR1 |= (0 << CR1_BIDIMODE); //1-line bidirectional mode if set
//SYSCFG->EXTICR[0] |= (0 << 0); //Enable
EXTI->IMR |= (1 << 0); //Enable interrupt
EXTI->RTSR |= (1 << 0); //set Risnig edge interrupt
EXTI->FTSR |= (0 << 0); //falling edge interrupt (disabled)
NVIC_EnableIRQ(EXTI0_IRQn);
SPI2->CR2 |= (1 << 7);
while(1){
GPIOD->ODR |= (1 << 12); // led ON
delay();
GPIOD->ODR &= ~(1 << 12); // led OFF
delay();
}
return 0;
GPIOB->MODER |= (2 << (2*13)); //Sets pin 13 as Alternate function
GPIOB->MODER |= (2 << (2*14)); //Sets pin 14 as Alternate function
GPIOB->MODER |= (2 << (2*15)); //Sets pin 15 as Alternate function
GPIOB->OTYPER |= PUSH_PULL_PIN_13;
GPIOB->OTYPER |= PUSH_PULL_PIN_14;
GPIOB->OTYPER |= PUSH_PULL_PIN_15;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOB->PUPDR |= PUPDR_PULLDOWN_PIN_13; // Pull down for CLK
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_14; // Pull up for MISO
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_15; // Pull up for MOSI
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_13; // 5 för AF5 till pin 13
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_14; // 5 för AF5 till pin 14
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_15; // 5 för AF5 till pin 15
GPIOA->MODER |= MODER_INPUT_PIN_0;
GPIOD->MODER |= MODER_OUTPUT_PIN_12; //Sets pin 12 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_13; //Sets pin 13 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_14; //Sets pin 14 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_15; //Sets pin 15 as output
GPIOD->OTYPER |= PUSH_PULL_PIN_12;
GPIOD->OTYPER |= PUSH_PULL_PIN_13;
GPIOD->OTYPER |= PUSH_PULL_PIN_14;
GPIOD->OTYPER |= PUSH_PULL_PIN_15;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_12;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_12; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_13; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_14; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_15; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_12; // 0 för AF0 till pin 12
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_13; // 0 för AF0 till pin 13
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_14; // 0 för AF0 till pin 14
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_15; // 0 för AF0 till pin 15
SPI2->CR1 |= (0 << CR1_CLOCK_PHASE); //Set clockphase in CR1 register
SPI2->CR1 |= (1 << CR1_CLOCK_POLARITY); //Set polarity in CR1 register
SPI2->CR1 |= (4 << CR1_BAUD_RATE); //Set baudrate
SPI2->CR1 |= (1 << CR1_DATA_FRAME_FORMAT); //16-bit transmission
SPI2->CR1 |= (1 << CR1_ENABLE_SPI); //Enable SPI
SPI2->CR1 |= (1 << CR1_MASTER_SELECT); //MASTER SELECTION
SPI2->CR1 |= (1 << CR1_LSB_FIRST); //LSB FIRST
SPI2->CR1 |= (1 << CR1_SLAVE_SELECT); //SSI set
SPI2->CR1 |= (1 << CR1_SW_SLAVE_MANAGE); //SSM, software slave management selected, which means SSI will be used insted of I/O
SPI2->CR1 |= (0 << CR1_RECEIVE_ONLY); //Transmit and Receive
SPI2->CR1 |= (0 << CR1_CRC_TRANSFER); //NOT USED, CRC
//SPI2->CR1 |= (0 << CR1_CRC_CALCULATION); //NOT USED, CRC calculation disabled
//SPI2->CR1 |= (0 << CR1_BIDIOE); //enable transmit-only if set
SPI2->CR1 |= (0 << CR1_BIDIMODE); //1-line bidirectional mode if set
//SYSCFG->EXTICR[0] |= (0 << 0); //Enable
EXTI->IMR |= (1 << 0); //Enable interrupt
EXTI->RTSR |= (1 << 0); //set Risnig edge interrupt
EXTI->FTSR |= (0 << 0); //falling edge interrupt (disabled)
NVIC_EnableIRQ(EXTI0_IRQn);
SPI2->CR2 |= (1 << 7);
while(1){
GPIOD->ODR |= (1 << 12); // led ON
delay();
GPIOD->ODR &= ~(1 << 12); // led OFF
delay();
}
return 0;
GPIOB->MODER |= (2 << (2*13)); //Sets pin 13 as Alternate function
GPIOB->MODER |= (2 << (2*14)); //Sets pin 14 as Alternate function
GPIOB->MODER |= (2 << (2*15)); //Sets pin 15 as Alternate function
GPIOB->OTYPER |= PUSH_PULL_PIN_13;
GPIOB->OTYPER |= PUSH_PULL_PIN_14;
GPIOB->OTYPER |= PUSH_PULL_PIN_15;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOB->PUPDR |= PUPDR_PULLDOWN_PIN_13; // Pull down for CLK
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_14; // Pull up for MISO
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_15; // Pull up for MOSI
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_13; // 5 för AF5 till pin 13
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_14; // 5 för AF5 till pin 14
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_15; // 5 för AF5 till pin 15
GPIOA->MODER |= MODER_INPUT_PIN_0;
GPIOD->MODER |= MODER_OUTPUT_PIN_12; //Sets pin 12 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_13; //Sets pin 13 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_14; //Sets pin 14 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_15; //Sets pin 15 as output
GPIOD->OTYPER |= PUSH_PULL_PIN_12;
GPIOD->OTYPER |= PUSH_PULL_PIN_13;
GPIOD->OTYPER |= PUSH_PULL_PIN_14;
GPIOD->OTYPER |= PUSH_PULL_PIN_15;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_12;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_12; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_13; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_14; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_15; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_12; // 0 för AF0 till pin 12
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_13; // 0 för AF0 till pin 13
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_14; // 0 för AF0 till pin 14
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_15; // 0 för AF0 till pin 15
SPI2->CR1 |= (0 << CR1_CLOCK_PHASE); //Set clockphase in CR1 register
SPI2->CR1 |= (1 << CR1_CLOCK_POLARITY); //Set polarity in CR1 register
SPI2->CR1 |= (4 << CR1_BAUD_RATE); //Set baudrate
SPI2->CR1 |= (1 << CR1_DATA_FRAME_FORMAT); //16-bit transmission
SPI2->CR1 |= (1 << CR1_ENABLE_SPI); //Enable SPI
SPI2->CR1 |= (1 << CR1_MASTER_SELECT); //MASTER SELECTION
SPI2->CR1 |= (1 << CR1_LSB_FIRST); //LSB FIRST
SPI2->CR1 |= (1 << CR1_SLAVE_SELECT); //SSI set
SPI2->CR1 |= (1 << CR1_SW_SLAVE_MANAGE); //SSM, software slave management selected, which means SSI will be used insted of I/O
SPI2->CR1 |= (0 << CR1_RECEIVE_ONLY); //Transmit and Receive
SPI2->CR1 |= (0 << CR1_CRC_TRANSFER); //NOT USED, CRC
//SPI2->CR1 |= (0 << CR1_CRC_CALCULATION); //NOT USED, CRC calculation disabled
//SPI2->CR1 |= (0 << CR1_BIDIOE); //enable transmit-only if set
SPI2->CR1 |= (0 << CR1_BIDIMODE); //1-line bidirectional mode if set
//SYSCFG->EXTICR[0] |= (0 << 0); //Enable
EXTI->IMR |= (1 << 0); //Enable interrupt
EXTI->RTSR |= (1 << 0); //set Risnig edge interrupt
EXTI->FTSR |= (0 << 0); //falling edge interrupt (disabled)
NVIC_EnableIRQ(EXTI0_IRQn);
SPI2->CR2 |= (1 << 7);
while(1){
GPIOD->ODR |= (1 << 12); // led ON
delay();
GPIOD->ODR &= ~(1 << 12); // led OFF
delay();
}
return 0;
}请使用stm32f407xx.h文件中适当的宏定义。最好阅读：
GPIOB->MODER |= (2 << (2*13)); //Sets pin 13 as Alternate function
GPIOB->MODER |= (2 << (2*14)); //Sets pin 14 as Alternate function
GPIOB->MODER |= (2 << (2*15)); //Sets pin 15 as Alternate function
GPIOB->OTYPER |= PUSH_PULL_PIN_13;
GPIOB->OTYPER |= PUSH_PULL_PIN_14;
GPIOB->OTYPER |= PUSH_PULL_PIN_15;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOB->PUPDR |= PUPDR_PULLDOWN_PIN_13; // Pull down for CLK
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_14; // Pull up for MISO
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_15; // Pull up for MOSI
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_13; // 5 för AF5 till pin 13
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_14; // 5 för AF5 till pin 14
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_15; // 5 för AF5 till pin 15
GPIOA->MODER |= MODER_INPUT_PIN_0;
GPIOD->MODER |= MODER_OUTPUT_PIN_12; //Sets pin 12 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_13; //Sets pin 13 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_14; //Sets pin 14 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_15; //Sets pin 15 as output
GPIOD->OTYPER |= PUSH_PULL_PIN_12;
GPIOD->OTYPER |= PUSH_PULL_PIN_13;
GPIOD->OTYPER |= PUSH_PULL_PIN_14;
GPIOD->OTYPER |= PUSH_PULL_PIN_15;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_12;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_12; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_13; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_14; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_15; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_12; // 0 för AF0 till pin 12
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_13; // 0 för AF0 till pin 13
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_14; // 0 för AF0 till pin 14
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_15; // 0 för AF0 till pin 15
SPI2->CR1 |= (0 << CR1_CLOCK_PHASE); //Set clockphase in CR1 register
SPI2->CR1 |= (1 << CR1_CLOCK_POLARITY); //Set polarity in CR1 register
SPI2->CR1 |= (4 << CR1_BAUD_RATE); //Set baudrate
SPI2->CR1 |= (1 << CR1_DATA_FRAME_FORMAT); //16-bit transmission
SPI2->CR1 |= (1 << CR1_ENABLE_SPI); //Enable SPI
SPI2->CR1 |= (1 << CR1_MASTER_SELECT); //MASTER SELECTION
SPI2->CR1 |= (1 << CR1_LSB_FIRST); //LSB FIRST
SPI2->CR1 |= (1 << CR1_SLAVE_SELECT); //SSI set
SPI2->CR1 |= (1 << CR1_SW_SLAVE_MANAGE); //SSM, software slave management selected, which means SSI will be used insted of I/O
SPI2->CR1 |= (0 << CR1_RECEIVE_ONLY); //Transmit and Receive
SPI2->CR1 |= (0 << CR1_CRC_TRANSFER); //NOT USED, CRC
//SPI2->CR1 |= (0 << CR1_CRC_CALCULATION); //NOT USED, CRC calculation disabled
//SPI2->CR1 |= (0 << CR1_BIDIOE); //enable transmit-only if set
SPI2->CR1 |= (0 << CR1_BIDIMODE); //1-line bidirectional mode if set
//SYSCFG->EXTICR[0] |= (0 << 0); //Enable
EXTI->IMR |= (1 << 0); //Enable interrupt
EXTI->RTSR |= (1 << 0); //set Risnig edge interrupt
EXTI->FTSR |= (0 << 0); //falling edge interrupt (disabled)
NVIC_EnableIRQ(EXTI0_IRQn);
SPI2->CR2 |= (1 << 7);
while(1){
GPIOD->ODR |= (1 << 12); // led ON
delay();
GPIOD->ODR &= ~(1 << 12); // led OFF
delay();
}
return 0;
TIM2->DIER |= TIM_DIER_UIE; /* interrupt enable on 1st channel */
GPIOB->MODER |= (2 << (2*13)); //Sets pin 13 as Alternate function
GPIOB->MODER |= (2 << (2*14)); //Sets pin 14 as Alternate function
GPIOB->MODER |= (2 << (2*15)); //Sets pin 15 as Alternate function
GPIOB->OTYPER |= PUSH_PULL_PIN_13;
GPIOB->OTYPER |= PUSH_PULL_PIN_14;
GPIOB->OTYPER |= PUSH_PULL_PIN_15;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOB->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOB->PUPDR |= PUPDR_PULLDOWN_PIN_13; // Pull down for CLK
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_14; // Pull up for MISO
GPIOB->PUPDR |= PUPDR_PULLUP_PIN_15; // Pull up for MOSI
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_13; // 5 för AF5 till pin 13
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_14; // 5 för AF5 till pin 14
GPIOB->AFR[1] |= ALT_FUNC_AF5_PIN_15; // 5 för AF5 till pin 15
GPIOA->MODER |= MODER_INPUT_PIN_0;
GPIOD->MODER |= MODER_OUTPUT_PIN_12; //Sets pin 12 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_13; //Sets pin 13 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_14; //Sets pin 14 as output
GPIOD->MODER |= MODER_OUTPUT_PIN_15; //Sets pin 15 as output
GPIOD->OTYPER |= PUSH_PULL_PIN_12;
GPIOD->OTYPER |= PUSH_PULL_PIN_13;
GPIOD->OTYPER |= PUSH_PULL_PIN_14;
GPIOD->OTYPER |= PUSH_PULL_PIN_15;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_12;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_13;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_14;
GPIOD->OSPEEDR |= OSPEEDR_MEDIUM_PIN_15;
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_12; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_13; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_14; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->PUPDR |= PUPDR_PULLDOWN_PIN_15; //Frågetecken på denna, ska det vara 0 1 eller 2??
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_12; // 0 för AF0 till pin 12
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_13; // 0 för AF0 till pin 13
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_14; // 0 för AF0 till pin 14
GPIOD->AFR[1] |= ALT_FUNC_AF0_PIN_15; // 0 för AF0 till pin 15
SPI2->CR1 |= (0 << CR1_CLOCK_PHASE); //Set clockphase in CR1 register
SPI2->CR1 |= (1 << CR1_CLOCK_POLARITY); //Set polarity in CR1 register
SPI2->CR1 |= (4 << CR1_BAUD_RATE); //Set baudrate
SPI2->CR1 |= (1 << CR1_DATA_FRAME_FORMAT); //16-bit transmission
SPI2->CR1 |= (1 << CR1_ENABLE_SPI); //Enable SPI
SPI2->CR1 |= (1 << CR1_MASTER_SELECT); //MASTER SELECTION
SPI2->CR1 |= (1 << CR1_LSB_FIRST); //LSB FIRST
SPI2->CR1 |= (1 << CR1_SLAVE_SELECT); //SSI set
SPI2->CR1 |= (1 << CR1_SW_SLAVE_MANAGE); //SSM, software slave management selected, which means SSI will be used insted of I/O
SPI2->CR1 |= (0 << CR1_RECEIVE_ONLY); //Transmit and Receive
SPI2->CR1 |= (0 << CR1_CRC_TRANSFER); //NOT USED, CRC
//SPI2->CR1 |= (0 << CR1_CRC_CALCULATION); //NOT USED, CRC calculation disabled
//SPI2->CR1 |= (0 << CR1_BIDIOE); //enable transmit-only if set
SPI2->CR1 |= (0 << CR1_BIDIMODE); //1-line bidirectional mode if set
//SYSCFG->EXTICR[0] |= (0 << 0); //Enable
EXTI->IMR |= (1 << 0); //Enable interrupt
EXTI->RTSR |= (1 << 0); //set Risnig edge interrupt
EXTI->FTSR |= (0 << 0); //falling edge interrupt (disabled)
NVIC_EnableIRQ(EXTI0_IRQn);
SPI2->CR2 |= (1 << 7);
while(1){
GPIOD->ODR |= (1 << 12); // led ON
delay();
GPIOD->ODR &= ~(1 << 12); // led OFF
delay();
}
return 0;
TIM2->DIER |=（1 AFR[1]|=（0 CR2 |=（1）我忘记了什么？有没有我没有配置的寄存器？功能性，当按下用户按钮时，主机应该发送数据，这将启动一个中断，发送应该在名为“void EXTI0|IRQHandler（）的中断函数中完成。此中断工作正常，按下按钮时LED以不同的颜色闪烁。我现在改为宏。我认为最开始的错误。LED应该是0。没错，应该是28。但这并不能解决SPI的问题，这只是针对LED编辑3：我试图设置控制寄存器，以便TXE位当tx缓冲区为空时，状态寄存器被设置，所以我知道何时发送下一个字节。我一定错过了配置某些总线或寄存器或其他东西。